Bond Machine Knitting - Handknit to Machine Knit Conversion

Date: Wed, 03 Sep 1997 06:42:45 -0700
From: Naomi Moore (gnomi@ibm.net)
Subject: [BOND] Hand Knit to Machine Knit Pattern Conversion

A few people have asked for methods of converting handknit patterns into
machine knit patterns.  This is what I have devised for myself so far:

1)  Use the program GraphPaper, which is available at various sites.  (I
would try http://www.shareware.com and search for "graph" or "paper" under
"all versions of Windows.  I think the file name is gpaper.exe.)  This
program is designed for Win 3.1 but works just fine in Win95.  Anyhow, the
beauty of this little program is that you can set the graph paper to
anything you want, as well as have bold lines.  Play with it to see what
you can produce.

I set up the graph so the squares become longer, turning into rectangles.

2.  Determine your gauge by making swatches with your keyplate.  If there
are colors in your pattern, such as for a fair isle technique, swatch with
those as well as this will influence your gauge.  Wash and dry your swatch
and then measure it, using your handy ruler to determine stitches per inch
and per row (the latter is important if you are doing an intarsia design).
Compare it with gauge suggested by the pattern.  If you are doing plain
knitting, don't worry too much about the handknit pattern rows-per-inch.

I usually will make a swatch using the different keyplates, dividing them
by making eyelets to demarcate them.  This way I will know which keyplate
did what (be sure to write down the keyplates you used if some time will
pass between swatch and project!).

3.  Next step is to convert hand knit stitches and rows per inch to match
your chosen keyplate.  For example, if the pattern says "20 st. and 24 rows
= 10 cm  (4 in.)" then you know that you need 5 st. per inch and 6 rows per
inch for the handknit pattern.  Let's say your chosen keyplate gives you
5.25 st. per inch and 6.25 rows per inch.  

You have chosen to knit a size medium, casting on 100 st. for the back,
increasing after ribbing to 110 stitches.  5 into 110 gives a measurement
of 22 inches.  Using your calculator, multiply 22 by 5.25 and the result is
115.5.  Look at the pattern.  Is the large pattern close to this in number,
by one or 2 stitches?  If yes, then cast on as if for the large pattern.
Make a note somewhere of this.

If you are knitting just a plain pattern, solid colors, then just note the
length to the armhole decrease if there is one, or to the shoulder.  Take
that length, say of 15 inches (in size medium since that is what size you
are), and multiply 6.25 by 15 to get a total of 93.75 rows.  Choose 94 or
93 rows.  BUT!!  Does the pattern read "15 inches from beginning of
ribbing"?  If it does, then you must subtract the ribbing length if you add
the ribbing by turning your knitting over, or by knitting it later by hand.
 Thus, if your ribbing is 2.5 inches, you need to subtract the 2.5 from 15,
resulting in 12.5 inches.  This then is multiplied by your rows per inch:
12.5 x 6.25 = 78.13 rows.  Choose 78 rows.  Write this down.

You will also apply this to your armhole length and sleeve length, alway
accounting for ribbing or other finishes.

If your swatch is similar in size to your handknit pattern, use the same
decreases for armholes and for sleeves and collars and necklines.  For
necklines you might add an extra decrease to make sure the neck is not too
tight on a crew or turtleneck.

The problem comes from intarsia or other geometric patterns.  My own
experience as a handknitter leads me just say follow the pattern as
written, perhaps adding a few rows of plain knitting, or an extra pattern
if you knit more rows per inch than the pattern.  Our hypothetical swatch
was smaller than the handknit swatch recommendation, so this is where you
would add.  If your swatch is looser than suggested, you can subtract some
rows.  If it is a large or complicated pattern, work out the math by
converting the rows per inch into your new gauge.  Thus, if you have a
repeat pattern of 27 rows, 27 divided by 6 is 4.5 inches.  27 rows divided
by 4.32 inches.  Over 22 inches from bottom to top, there will by a
possible loss of length that may or may not be worth worrying about; this
is something you need to determine.

You can determine this somewhat by dividing your pattern repeat length for
the handknit into the total finished sweater length.  For instance, if your
total sweater is 22 inches, not including ribbing, the pattern is 22 inches
x 6 rows per inch, for a total of 132 rows in the handknit pattern.  If you
just follow your 27 row pattern, you will need to multiply your machine
rows by 22, which is 137.5 rows.  This is close enough or not, depending on
the nature of the pattern as well as your own taste.  

4.  Ok, so now about the graph paper.  In each square I write down the row
number, if I need to increase (I) or decrease (D), change a pattern or a
color.  So, for a sleeve, in plain knit with increases every 3rd row, I
would have in each box the following (read each line as a different box):
	1
	1
	1, I
	1
	1
	1, I
For stripes I have done the following:
	1
	1
	1, I
	1, A (for contrast color A)
and so on.

The point is to devise your own short hand.  I write P for Pattern for a
fair isle technique, so:
	1
	1
	1, I,  PA

Each time I do something, I cross it off AFTER I do it; you might want to
do it BEFORE you do it, but until you determine your style, write down in
your notes what you are doing (i.e. crossing out each letter as you do it,
or before you do it) so that you will not forget it.

I don't have a row counter for my ISM, though I may get one soon enough for
just plain knitting; it would be easier I know that.  But for now, this is
working out just fine for me.

Oh, for pattern repeats, I put bold lines between each repeat.  At the
moment I am working on a sweater with the following design:

- --x---x--
- --x---x--
- --x---x--
- --x---x--
x---x---x
x---x---x
x---x---x
x---x---x

Here, I have a bold line between every 4th square so that it reminds me to
change colors and patterning.

All this is pretty windy, so I hope it helps.  I expect that the various
knitting software programs might also be of some help, but I don't like to
do everything on the computer!

Naomi
gnomi@ibm.net

------------------------------

Date: Tue, 30 Jun 1998 21:50:15 -0500
From: cpolfer@juno.com (Cindy S Polfer)
Subject: [BOND] Knitting through back loop

If you knit through the back loop in hand knitting you are twisting the
stitch.  To do this on the Bond work the following:

Before knitting the row where you knit through the back loop,  do this to
the designated stitch.  With your 1-prong transfer tool, insert tool into
the stitch hanging on the needle from knit side to purl side (that is,
from the side of fabric closest to the bed and poking your tool out of
the stitch pointing towards you). Drop your stitch onto the tool by
pushing the needle butt forward and then back, dropping the stitch onto
the tool.  Now take your tool (it should be lying horizontal) and turn it
CLOCKWISE 180 degrees so that the 1-prong tool end touches the empty
needle hook.  Place stitch on needle.  When you knit the row with your
carriage, you will be knitting through the back loop.

Hope this answers your question.  If not, e-mail me.
Sincerely,

Cindy Polfer - cpolfer@juno.com
Big Rock, IL

Back ArrowBack to the Bond List Thoughts Page Back to Steph's Home Page E-Mail
Please e-mail any comments to me at steph@stephthornton.co.uk

Author : Steph Thornton.
Last modified on : 1st July 1998.